Prepare with Fortinet : NSE5_FSW_AD-7.6 exam braindumps as your best preparation materials

Refer to the exhibit.

You just connected three FortiSwitch devices:Core-1,Core-2, andAccess-1. Core-1 and Core-2 both connect to Access-1 for redundancy. All switches are managed by FortiGate, which uses port4 as the FortiLink interface. After you enable the uplink ports on Core-2, you notice that port3 on Access-1 enters the Discarding STP state. What is the most likely cause of this behavior? (Choose one answer)

• A. Bridge Protocol Data Unit (BPDU) Guard is enabled, which shuts down the port after it receives BPDUs.
• B. FortiGate is not running Spanning Tree Protocol (STP) on the FortiLink interface.
• C. Access-1 is not authorized by FortiGate.
• D. Core-2 has the lowest bridge priority.

What happens when a routed VLAN interface (RVI) is configured on a FortiSwitch port or trunk? (Choose one answer)

• A. The port becomes a layer 3 interface with VLAN 4095 assigned automatically.1
• B. All VLANs on the port are terminated in a trunk by default.
• C. VLAN 1 is automatically assigned for management.
• D. The port becomes a layer 3 interface and assigned to VLAN 1.

You are deploying a small office network with a single FortiGate and a single FortiSwitch. The office currently has moderate traffic, but the IT team expects the network to grow in the near future, adding more FortiSwitch devices and endpoints. Which FortiLink configuration should you deploy to provide the best combination of current performance and scalability for future growth? (Choose one answer)

• A. Configure FortiLink as a link aggregation group (LAG) interface.
• B. Configure FortiLink as a multichassis LAG (MCLAG) interface.2
• C. Configure FortiLink using software-based switch interfaces.
• D. Configure FortiLink using hardware-based switch interfaces.1

You are managing FortiSwitch ports from a FortiGate device with multiple VDOMs. Which two methods can you use to assign FortiSwitch ports to VDOMs? (Choose two answers)

• A. Use interface role mapping to dynamically assign FortiSwitch ports to VDOMs based on Dynamic Host Configuration Protocol (DHCP) scope
• B. Using a virtual port pool (VPP) to create virtualized ports that can be assigned to different VDOMs
• C. Use FortiGate policies to control inter-VDOM traffic for FortiSwitch ports
• D. Assigning the port directly to a specific VDOM for dedicated physical isolation

Exhibit.
port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

• A. port1 was shut down by loop guard protection.
• B. STP triggered a loop and applied loop guard protection on port1.
• C. Loop guard frame sourced from port1 was received on port1.
• D. An endpoint sent a BPDU on port1 that it received from another interface.

Refer to the exhibit.

You just connected three FortiSwitch devices:Core-1,Core-2, andAccess-1. Core-1 and Core-2 both connect to Access-1 for redundancy. All switches are managed by FortiGate, which uses port4 as the FortiLink interface. After you enable the uplink ports on Core-2, you notice that port3 on Access-1 enters the Discarding STP state. What is the most likely cause of this behavior? (Choose one answer)

• A. Bridge Protocol Data Unit (BPDU) Guard is enabled, which shuts down the port after it receives BPDUs.
• B. FortiGate is not running Spanning Tree Protocol (STP) on the FortiLink interface.
• C. Access-1 is not authorized by FortiGate.
• D. Core-2 has the lowest bridge priority.

What happens when a routed VLAN interface (RVI) is configured on a FortiSwitch port or trunk? (Choose one answer)

• A. The port becomes a layer 3 interface with VLAN 4095 assigned automatically.1
• B. All VLANs on the port are terminated in a trunk by default.
• C. VLAN 1 is automatically assigned for management.
• D. The port becomes a layer 3 interface and assigned to VLAN 1.

You are deploying a small office network with a single FortiGate and a single FortiSwitch. The office currently has moderate traffic, but the IT team expects the network to grow in the near future, adding more FortiSwitch devices and endpoints. Which FortiLink configuration should you deploy to provide the best combination of current performance and scalability for future growth? (Choose one answer)

• A. Configure FortiLink as a link aggregation group (LAG) interface.
• B. Configure FortiLink as a multichassis LAG (MCLAG) interface.2
• C. Configure FortiLink using software-based switch interfaces.
• D. Configure FortiLink using hardware-based switch interfaces.1

You are managing FortiSwitch ports from a FortiGate device with multiple VDOMs. Which two methods can you use to assign FortiSwitch ports to VDOMs? (Choose two answers)

• A. Use interface role mapping to dynamically assign FortiSwitch ports to VDOMs based on Dynamic Host Configuration Protocol (DHCP) scope
• B. Using a virtual port pool (VPP) to create virtualized ports that can be assigned to different VDOMs
• C. Use FortiGate policies to control inter-VDOM traffic for FortiSwitch ports
• D. Assigning the port directly to a specific VDOM for dedicated physical isolation

Exhibit.
port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

• A. port1 was shut down by loop guard protection.
• B. STP triggered a loop and applied loop guard protection on port1.
• C. Loop guard frame sourced from port1 was received on port1.
• D. An endpoint sent a BPDU on port1 that it received from another interface.